PressureDependMultiYield Material

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

PressureDependMultiYield material is an elastic-plastic material for simulating the essential response characteristics of pressure sensitive soil materials under general loading conditions. Such characteristics include dilatancy (shear-induced volume contraction or dilation) and non-flow liquefaction (cyclic mobility), typically exhibited in sands or silts during monotonic or cyclic loading.

When this material is employed in regular solid elements (e.g., FourNodeQuad, Brick), it simulates drained soil response. To simulate soil response under fully undrained condition, this material may be either embedded in a FluidSolidPorousMaterial, or used with one of the solid-fluid fully coupled elements (Four Node Quad u-p Element, Nine Four Node Quad u-p Element, Brick u-p Element, Twenty Eight Node Brick u-p Element) with very low permeability. To simulate partially drained soil response, this material should be used with a solid-fluid fully coupled element with proper permeability values.

During the application of gravity load (and static loads if any), material behavior is linear elastic. In the subsequent dynamic (fast) loading phase(s), the stress-strain response is elastic-plastic (see updateMaterialStage). Plasticity is formulated based on the multi-surface (nested surfaces) concept, with a non-associative flow rule to reproduce dilatancy effect. The yield surfaces are of the Drucker-Prager type.

OUTPUT INTERFACE:

The following information may be extracted for this material at a given integration point, using the OpenSees Element Recorder facility (McKenna and Fenves 2001)^®: "stress", "strain", "backbone", or "tangent".

For 2D problems, the stress output follows this order: σ_xx, σ_yy, σ_zz, σ_xy, η_r, where η_r is the ratio between the shear (deviatoric) stress and peak shear strength at the current confinement (0<=η_r<=1.0). The strain output follows this order: ε_xx, ε_yy, γ_xy.

For 3D problems, the stress output follows this order: σ_xx, σ_yy, σ_zz, σ_xy, σ_yz, σ_zx, η_r, and the strain output follows this order: ε_xx, ε_yy, ε_zz, γ_xy, γ_yz, γ_zx.

The "backbone" option records (secant) shear modulus reduction curves at one or more given confinements. The specific recorder command is as follows:

recorder Element -ele $eleNum -file $fName -dT $deltaT material $GaussNum backbone $p1 <$p2 …>

where p1, p2, … are the confinements at which modulus reduction curves are recorded. In the output file, corresponding to each given confinement there are two columns: shear strain γ and secant modulus G_s. The number of rows equals the number of yield surfaces.

nDMaterial PressureDependMultiYield $tag $nd $rho $refShearModul $refBulkModul $frictionAng $peakShearStra $refPress $pressDependCoe $PTAng $contrac $dilat1 $dilat2 $liquefac1 $liquefac2 $liquefac3 <$noYieldSurf=20 <$r1 $Gs1 …> $e=0.6 $cs1=0.9 $cs2=0.02 $cs3=0.7 $pa=101 <$c=0.3>>

---

$tag	A positive integer uniquely identifying the material among all nDMaterials.
$nd	Number of dimensions, 2 for plane-strain, and 3 for 3D analysis.
$rho	Saturated soil mass density.
$refShearModul (Gr)	Reference low-strain shear modulus, specified at a reference mean effective confining pressure refPress of p’r (see below).
$refBulkModul (Br)	Reference bulk modulus, specified at a reference mean effective confining pressure refPress of p’r (see below).
$frictionAng (Φ)	Friction angle at peak shear strength, in degrees.
$peakShearStra (γmax)	An octahedral shear strain at which the maximum shear strength is reached, specified at a reference mean effective confining pressure refPress of p’r (see below). Octahedral shear strain is defined as:
$refPress (p’r)	Reference mean effective confining pressure at which Gr, Br, and γmax are defined.
$pressDependCoe (d)	A positive constant defining variations of G and B as a function of instantaneous effective confinement p’:
$PTAng (ΦPT)	Phase transformation angle, in degrees.
$contrac	A non-negative constant defining the rate of shear-induced volume decrease (contraction) or pore pressure buildup. A larger value corresponds to faster contraction rate.
$dilat1, $dilat2	Non-negative constants defining the rate of shear-induced volume increase (dilation). Larger values correspond to stronger dilation rate.
$liquefac1, $liquefac2, $liquefac3	Parameters controlling the mechanism of liquefaction-induced perfectly plastic shear strain accumulation, i.e., cyclic mobility. Set liquefac1 = 0 to deactivate this mechanism altogether. liquefac1 defines the effective confining pressure (e.g., 10 kPa in SI units or 1.45 psi in English units) below which the mechanism is in effect. Smaller values should be assigned to denser sands. Liquefac2 defines the maximum amount of perfectly plastic shear strain developed at zero effective confinement during each loading phase. Smaller values should be assigned to denser sands. Liquefac3 defines the maximum amount of biased perfectly plastic shear strain γb accumulated at each loading phase under biased shear loading conditions, as γb=liquefac2 x liquefac3. Typically, liquefac3 takes a value between 0.0 and 3.0. Smaller values should be assigned to denser sands. See the references listed at the end of this chapter for more information.
$noYieldSurf	Number of yield surfaces, optional (must be less than 40, default is 20). The surfaces are generated based on the hyperbolic relation defined in Note 2 below.
$r, $Gs	Instead of automatic surfaces generation (Note 2), you can define yield surfaces directly based on desired shear modulus reduction curve. To do so, add a minus sign in front of noYieldSurf, then provide noYieldSurf pairs of shear strain (γ) and modulus ratio (Gs) values. For example, to define 10 surfaces: … -10γ1Gs1 … γ10Gs10 … See Note 3 below for some important notes.
$e	Initial void ratio, optional (default is 0.6).
$cs1, $cs2, $cs3, $pa	Parameters defining a straight critical-state line ec in e-p’ space. If cs3=0, ec = cs1-cs2 log(p'/pa) else (Li and Wang, JGGE, 124(12)), ec = cs1-cs2(p'/pa)cs3 where pa is atmospheric pressure for normalization (typically 101 kPa in SI units, or 14.65 psi in English units). All four constants are optional (default values: cs1=0.9, cs2=0.02, cs3=0.7, pa =101 kPa).
$c	Numerical constant (default value = 0.3 kPa)

NOTE:

1. The friction angle Φ defines the variation of peak (octahedral) shear strength τ_f as a function of current effective confinement p’:

Octahedral shear stress is defined as:

2. (Automatic surface generation) At a constant confinement p’, the shear stress τ(octahedral) - shear strain γ (octahedral) nonlinearity is defined by a hyperbolic curve (backbone curve):

where γ_r satisfies the following equation at p’_r:

3. (User defined surfaces) The user specified friction angle Φ is ignored. Instead, Φ is defined as follows:

where σ_m is the product of the last modulus and strain pair in the modulus reduction curve. Therefore, it is important to adjust the backbone curve so as to render an appropriate Φ. If the resulting Φ is smaller than the phase transformation angle Φ_PT, Φ_PT is set equal to Φ. Also remember that improper modulus reduction curves can result in strain softening response (negative tangent shear modulus), which is not allowed in the current model formulation. Finally, note that the backbone curve varies with confinement, although the variations are small within commonly interested confinement ranges. Backbone curves at different confinements can be obtained using the OpenSees element recorder facility (see OUTPUT INTERFACE above).

4. The last five optional parameters are needed when critical-state response (flow liquefaction) is anticipated. Upon reaching the critical-state line, material dilatancy is set to zero.

5. SUGGESTED PARAMETER VALUES

For user convenience, a table is provided below as a quick reference for selecting parameter values. However, use of this table should be of great caution, and other information should be incorporated wherever possible.

Parameters	Loose Sand (15%-35%)	Medium Sand (35%-65%)	Medium-dense Sand (65%-85%)	Dense Sand (85%-100%)
rho	1.7 ton/m3 or 1.59x10-4 (lbf)(s2)/in4	1.9 ton/m3 or 1.778x10-4 (lbf)(s2)/in4	2.0 ton/m3 or 1.872x10-4 (lbf)(s2)/in4	2.1 ton/m3 or 1.965x10-4 (lbf)(s2)/in4
refShearModul (at p’r=80 kPa or 11.6 psi)	5.5x104 kPa or 7.977x103 psi	7.5x104 kPa or 1.088x104 psi	1.0x105 kPa or 1.45x104 psi	1.3x105 kPa or 1.885x104 psi
refBulkModu (at p’r=80 kPa or 11.6 psi)	1.5x105 kPa or 2.176x104 psi	2.0x105 kPa or 2.9x104 psi	3.0x105 kPa or 4.351x104 psi	3.9x105 kPa or 5.656x104 psi
frictionAng	29	33	37	40
peakShearStra (at p’r=80 kPa or 11.6 psi)	0.1	0.1	0.1	0.1
refPress (p’r)	80 kPa or 11.6 psi	80 kPa or 11.6 psi	80 kPa or 11.6 psi	80 kPa or 11.6 psi
pressDependCoe	0.5	0.5	0.5	0.5
PTAng	29	27	27	27
contrac	0.21	0.07	0.05	0.03
dilat1	0.	0.4	0.6	0.8
dilat2	0	2	3	5
liquefac1	10 kPa or 1.45 psi	10 kPa or 1.45 psi	5 kPa or 0.725 psi	0
liquefac2	0.02	0.01	0.003	0
liquefac3	1	1	1	0
e	0.85	0.7	0.55	0.45

Pressure Dependent Material Examples:

Material in elastic, drained (or dry) state
Example 1	Single quadrilateral element, subjected to sinusoidal base shaking
Example 2	Single quadrilateral element, subjected to monotonic pushover (English units version)
Material in drained (or dry), elastic-plastic state
Example 3	Single quadrilateral element, subjected to sinusoidal base shaking
Example 4	Single quadrilateral element (inclined by 4 degrees), subjected to sinusoidal base shaking
Example 5	Single quadrilateral element, subjected to monotonic pushover
Example 6	Single 3D BbarBrick element, subjected to sinusoidal base shaking
Example 7	Single 3D BbarBrick element (inclined by 4 degrees), subjected to sinusoidal base shaking
Material in saturated, undrained elastic-plastic state (coupled with FluidSolidPorous Material)
Example 8	Single quadrilateral element, subjected to sinusoidal base shaking
Example 9	Single quadrilateral element, subjected to monotonic pushover
Example 10	Single quadrilateral element (inclined by 4 degrees), subjected to msinusoidal base shaking
Example 11	Single 3D BbarBrick element, subjected to sinusoidal base shaking
Example 12	Single 3D BbarBrick element (inclined by 4 degrees), subjected to sinusoidal base shaking
Example 13	A column of quadrilateral element (inclined by 4 degrees), subjected to sinusoidal base shaking
Material in saturated, undrained elastic-plastic state (with user defined modulus reduction curve)
Example 14	A column of quadrilateral element (inclined by 4 degrees), subjected to sinusoidal base shaking
Solid-Fluid fully coupled elements - quadUP element
Example 15	A column (2D plane strain quadUP element) of saturated, undrained Pressure Dependent material (inclined by 4 degrees), subjected to sinusoidal base shaking

Code Developed by: UC San Diego (Dr. Zhaohui Yang):

---

UC San Diego Soil Model:

• NDMaterial Command
  • UC San Diego soil models (Linear/Nonlinear, dry/drained/undrained soil response under general 2D/3D static/cyclic loading conditions (please visit UCSD for examples)
    • PressureIndependMultiYield Material
    • PressureDependMultiYield Material
    • PressureDependMultiYield02 Material
    • PressureDependMultiYield03 Material
  • UC San Diego Saturated Undrained soil
    • FluidSolidPorousMaterial

• Element Command
  • UC San Diego u-p element (saturated soil)
    • Four Node Quad u-p Element
    • Brick u-p Element
    • bbarQuad u-p Element
    • bbarBrick u-p Element
    • Nine Four Node Quad u-p Element
    • Twenty Eight Node Brick u-p Element
• Related References

---