FRPConfinedConcrete

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command is used to construct a uniaxial Megalooikonomou-Monti-Santini concrete material object with degraded linear unloading/reloading stiffness according to the work of Karsan-Jirsa and no tensile strength.

uniaxialMaterial FRPConfinedConcrete $matTag $fpc1 $fpc2 $epsc0 $D $c $Ej $Sj $tj $eju $S $fyh $dlong $dtrans $Es $vo $k

---

$matTag	integer tag identifying material.
$fpc1	concrete core compressive strength.
$fpc2	concrete cover compressive strength.
$epsc0	strain corresponding to unconfined concrete strength.
$D	diameter of the circular section.
$c	dimension of concrete cover (until the edge of steel stirrups)
$Ej	elastic modulus of the fiber reinforced polymer (FRP) jacket.
$Sj	clear spacing of the FRP strips - zero if it's continuous.
$tj	total thickness of the FRP jacket.
$eju	rupture strain of the FRP jacket from tensile coupons.
$S	spacing of the steel spiral/stirrups.
$fyh	yielding strength of the steel spiral/stirrups.
$dlong	diameter of the longitudinal bars of the circular section.
$dtrans	diameter of the steel spiral/stirrups.
$Es	elastic modulus of steel.
$vo	initial Poisson’s coefficient for concrete.
$k	reduction factor for the rupture strain of the FRP jacket, recommended values 0.5-0.8..

NOTES:

• IMPORTANT: The units of the input parameters should be in MPa, N, mm.

• Concrete compressive strengths and the corresponding strain should be input as positive values.

• When rupture of FRP jacket occurs due to dilation of concrete (lateral concrete strain exceeding reduced rupture strain of FRP jacket), the analysis is not terminated. Only a message “FRP Rupture” is plotted on the screen.

File:Example.jpg

EXAMPLES:

Example: Cantilever FRP-Confined Circular Reinforced Concrete Column under Cyclic Lateral Loading

Attach Figure 2 with title below the figure: Cantilever Column Model Definition.

The cantilever column was modeled by a linear beam element with the stiffness corresponding to flexural yielding and a fiber element used to capture the flexural hysteretic behavior at the plastic hinge. The length of the fiber element was assumed to be half of the column’s diameter. A rotational spring at the bottom of the column represents the longitudinal bar pullout from the footing and was assumed to have an elastic stiffness.

Attach file ExampleFRP.tcl (with a link) that can be downloaded and opened with Notepad.

Attach Figure 3. with title below the figure: Response of Cantilever FRP-Confined Circular Reinforced Concrete Column under Cyclic Lateral Loading.

---

REFEERENCES:

• MEGALOOIKONOMOU K.G., MONTI G., SANTINI S., “Constitutive Model for Fiber –Reinforced Polymer - and Tie – Confined Concrete”, ACI Structural Journal, Vol. 109, No. 4, July 2012, pp. 569-578.

• KARSAN, I.D., JIRSA, J.O., “Behaviour of concrete under compressive loadings”, Journal of Structural Division ASCE, Vol. 95, No. 12, 1969, pp. 2543-2563.

• PAPAVASILEIOU G.S., MEGALOOIKONOMOU K.G., “Numerical Simulation of FRP-Confined Circular Bridge Piers Using Opensees”, In Proceedings of: Opensees Days Italy (OSD), Second Italian Conference, University of Salerno, Fisciano, Salerno, Italy, June 10-11, 2015.

• GALLARDO – ZAFRA R., KAWASHIMA, K., “Analysis of CFRP RC Bridge Columns under Lateral Cyclic Loading”, Journal of Earthquake Engineering, Vol. 13, 2009, pp. 129-154.

---