SSPbrickUP Element

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command is used to construct a SSPbrickUP element object.

element SSPbrickUP $eleTag $iNode $jNode $kNode $lNode $mNode $nNode $pNode $qNode $matTag $fBulk $fDen $k1 $k2 $k3 $void $alpha <$b1 $b2 $b3>

$eleTag	unique integer tag identifying element object
$iNode $jNode $kNode $lNode $mNode $nNode $pNode $qNode	the eight nodes defining the element, input in counterclockwise order (same node number scheme as for the brickUP Element) (-ndm 3 -ndf 4)
$matTag	unique integer tag associated with previously-defined nDMaterial object
$fBulk	bulk modulus of the pore fluid
$fDen	mass density of the pore fluid
$k1 $k2 $k3	permeability coefficients in global x-, y-, and z-directions, respectively
$void	voids ratio
$alpha	spatial pressure field stabilization parameter (see notes below for more information)
$b1 $b2 $b3	constant body forces in global x-, y-, and z-directions, respectively (optional, default = 0.0)

---

The SSPbrickUP element is an extension of the SSPbrick Element for use in dynamic 3D analysis of fluid saturated porous media. A mixed displacement-pressure (u-p) formulation is used, based upon the work of Biot as extended by Zienkiewicz and Shiomi (1984).

The physical stabilization necessary to allow for reduced integration incorporates an enhanced assumed strain field, resulting in an element which is free from volumetric and shear locking. The elimination of shear locking results in greater coarse mesh accuracy in bending dominated problems, and the elimination of volumetric locking improves accuracy in nearly-incompressible problems. Analysis times are generally faster than corresponding full integration elements.

Equal-order interpolation is used for the displacement and pressure fields, thus, the SSPbrickUP element does not inherently pass the inf-sup condition, and is not fully acceptable in the incompressible-impermeable limit (the brickUP Element has the same issue). A stabilizing parameter is employed to permit the use of equal-order interpolation for the SSPbrickUP element. This parameter $alpha can be computed as

alpha = 0.25*(h^2)/(den*c^2)

where h is the element size, c is the speed of elastic wave propagation in the solid phase, and den is the mass density of the solid phase. The $alpha parameter should be a small number. With a properly defined $alpha parameter, the SSPbrickUP element can produce comparable results to a higher-order element such as the 20_8_BrickUP Element at a significantly lower computational cost and with a greater ease in mesh generation.

NOTES:

1. The SSPbrickUP element will only work in dynamic analysis.
2. For saturated soils, the mass density input into the associated nDMaterial object should be the saturated mass density.
3. The body forces input into the SSPbrickUP element should be the components of the gravitational vector, not the unit weight.
4. Fixing the pore pressure degree-of-freedom (dof 4) at a node is a drainage boundary condition at which zero pore pressure will be maintained throughout the analysis. Leaving the fourth dof free allows pore pressures to build at that node.
5. Valid queries to the SSPbrickUP element when creating an ElementalRecorder object correspond to those for the nDMaterial object assigned to the element (e.g., 'stress', 'strain'). Material response is recorded at the single integration point located in the center of the element.
6. The SSPbrickUP element was designed with intentions of duplicating the functionality of the brickUP Element. If an example is found where the SSPbrickUP element cannot do something that works for the brickUP Element, e.g., material updating, please contact the developers listed below so the bug can be fixed.

EXAMPLES:

SSPbrickUP element definition with element tag 1, nodes 1, 2, 3, 4, 5, 6, 7, and 8, material tag 1, bulk modulus of water (kPa), mass density of water (Mg/m^3), isotropic permeability of 1e-3, voids ratio of 0.7, alpha parameter of 6e-5, x- and y-directed body forces of zero, and z-directed body force of -9.81

element SSPbrickUP 1  1 2 3 4 5 6 7 8  1 2.2e6 1.0 1.0e-3 1.0e-3 1.0e-3 0.7 6.0e-5 0.0 0.0 -9.81

Elemental recorders for stress and strain when using the SSPbrickUP element (note the difference from the brickUP Element)

recorder Element -eleRange 1 $numElem -time -file stress.out  stress
recorder Element -eleRange 1 $numElem -time -file strain.out  strain

Pore pressure recorder for the SSPbrickUP element (pore pressure is the fourth degree-of-freedom)

recorder Node -nodeRange 1 $numNode -time -file porePressure.out -dof 4 vel

REFERENCES:

Zienkiewicz, O.C. and Shiomi, T. (1984). "Dynamic behavior of saturated porous media; the generalized Biot formulation and its numerical solution." International Journal for Numerical Methods in Geomechanics, 8, 71-96.

---

Code Developed by: Chris McGann, Pedro Arduino, & Peter Mackenzie-Helnwein, at the University of Washington

---