Shear LimitCurve

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command is used to construct a shear limit curve object that is used to define the point of shear failure for a LimitStateMaterial object. Point of shear failure is based on empirical drift capacity model from Chapter 2 of PEER 2003/01 report. After shear failure the response of LimitStateMaterial is forced to follow shear limit curve.

limitCurve Shear $curveTag $eleTag $rho $fc $b $h $d $Fsw $Kdeg $Fres $defType $forType <$ndI $ndJ $dof $perpDirn $delta>

---

$curveTag	unique LimitCurve tag
$eleTag	integer element tag for the associated beam-column element
$rho	transverse reinforcement ratio <math>(\frac{A_{st}}{bh})</math>
$fc	concrete compressive strength (psi)
$b	column width (in.)
$h	full column depth (in.)
$d	effective column depth (in.)
$Fsw	loating point value describing the amount of transverse reinforcement <math>(F_{sw} = \frac{A_{st}f_{yt}d_c}{s})</math>
$Kdeg	If positive: unloading stiffness of beam-column element (Kunload from Figure 4-8) if negative: slope of third branch of post-failure backbone (see Figure 4-6)
%Fres'	floating point value for the residual force capacity of the post-failure backbone (see Figure 4-6)
$defType	integer flag for type of deformation defining the abscissa of the limit curve 1 = maximum beam-column chord rotations 2 = drift based on displacment of nodes ndI and ndJ
$forType	nteger flag for type of force defining the ordinate of the limit curve. See NOTES 1. 0 = force in associated limit state material 1 = shear in beam-column element 2 = axial load in beam-column element
$ndI	nteger node tag for the first associated node (normally node I of $eleTag beam-column element)
$ndJ	integer node tag for the second associated node (normally node J of $eleTag beam-column element)
$dof	nodal degree of freedom to monitor for drift. See NOTES 2
$perpDirn	perpendicular global direction from which length is determined to compute drift. See Notes 2.
$delta	drift (floating point value) used to shift axial limit curve

NOTES:

1. Options 1 and 2 assume no member loads
2. 1 = X, 2 = Y, 3 = Z

---

EXAMPLE:

<tcl>CenterColShearSpring.tcl</tcl>

---

DESCRIPTION:

Modeling Failures in Existing Reinforced Concrete Columns by Ken Elwood: File:ElwoodCJCE2004.pdf

---

REFERENCES:

Elwood, K.J and Moehle, J.P., "Shake Table Tests and Analystical Studies on the Gravity Load Collapse of Reinforced Concrete Frames", Pacific Earthquake Engineering Research Center, University of California, Berkeley, CA. PEER 2003/01.

---

Code Developed by: Ken Elwood, University of British Columbia