ZeroLengthInterface2D

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

zeroLengthInterface2D is Node-to-Segment (NTS) frictional contact element used in two dimensional analysis for contact between elements. Please notice that any number of DOF (DOF>1) can be handled using this element (i.e. beam-solid, solid-solid as well as beam-beam contact) as oppose to zeroLengthContactNTS2D element).

element zeroLengthInterface2D $eleTag -cNdNum $cNdNum -rNdNum $rNdNum –dof $cdof $rdof -Nodes $Nodes $Kn $Kt $phi

---

$eleTag	unique element object tag
$cNdNum	Number of Constrained Nodes
$rNdNum	Number of Retained nodes
$cdof $rdof	Constrained and Retained degree of freedom
$Nodes ...	Constrained and Retained node tags respectively
$Kn	Penalty in normal direction
$Kt	Penalty in tangential direction
$phi	Friction angle in degrees

NOTES:

1. The contact element is node-to-segment (NTS) contact. The relation follows Mohr-Coulomb frictional law: <math>T = N \times tan(\phi)</math>, where <math>T</math> is the tangential force, <math>N</math> is normal force across the interface and <math>\phi\,\!</math> is friction angle.
2. For 2D contact, constrained nodes and retained nodes must be 2 DOF and notice that the constrained and retained nodes must be entered in counterclockwise order.
3. The resulting tangent from the contact element is non-symmetric. Switch to the non-symmetric matrix solver if convergence problem is experienced.
4. As opposed to node-to-node contact, predefined normal vector for node-to-segment (NTS) element is not required because contact normal will be calculated automatically at each step. And also this element can handle contact between different DOFs such as beam-beam, beam-solid and solid-solid.
5. contact element is implemented to handle large deformations.

EXAMPLE:

element zeroLengthInterface2D 1 -sNdNum 6 -mNdNum 6 –dof 2 3 -Nodes 5 10 12 3 9 11 1 4 2 8 7 3 1e8 1e8 16

Example 1:

This example simply shows the quadrilateral elements in normal contact on top of beam element. The top element is in normal downward uniform force. The Tcl script of this example can be found here.

Example 2:

This example shows two cantilever beams in contact. The beams were modeled using four-node quadrilateral elements and the end of top beam was subjected to a linearly increasing displacement. The Tcl scripts for this example can be found here.

The following Figure shows the deflections of the two beams.

REFERENCES:

1. P. Wriggers, V.T. Vu and E. Stein, Finite-element formulation of large deformation impact–contact problems with friction, Comput. Struct. 37 (1990), pp. 319–331.
2. Peter Wriggers. Computational Contact Mechanics. John Wiley & Sons Ltd. Chichester, 2002.

---

Code Developed by: Roozbeh G. Mikola, UC Berkeley and N. Sitar, UC Berkeley