Velocity and Normal Force Dependent Friction

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command is used to construct a VelNormalFrcDep friction model object.

frictionModel VelNormalFrcDep $frnTag $aSlow $nSlow $aFast $nFast $alpha0 $alpha1 $alpha2 $maxMuFact

---

$frnTag	unique friction model object tag
$aSlow	constant for coefficient of friction at low velocity
$nSlow	exponent for coefficient of friction at low velocity
$aFast	constant for coefficient of friction at high velocity
$nFast	exponent for coefficient of friction at high velocity
$alpha0	constant rate parameter coefficient
$alpha1	linear rate parameter coefficient
$alpha2	quadratic rate parameter coefficient
$maxMuFact	factor for determining the maximum coefficient of friction. This value prevents the friction coefficient from exceeding an unrealistic maximum value when the vertical force becomes very small. The maximum friction coefficient is determined from μ_fast, for example μ_1 ≤ $maxMuFac.$mu1fast.

The friction model is defined as follows:

1. Define the friction coefficient at slow (μSlow) and fast (μFast) velocity [1] (Figure 1):

μSlow = aSlow*N^(nSlow-1)

μFast = aFast*N^(nFast-1)

where aSlow, aFast, nSlow ≤ 1, nFast ≤ 1 are constants that determine the friction coefficient models. As the friction coefficients μSlow and μFast are unitless, the user must be careful to define the constants to coincide with the units of the model input data.

2. The friction coefficient as a function of velocity is [2]:

μ = μFast - (μFast-μSlow )*exp(-a*udot)

where udot is velocity and a is a rate parameter.

3. In this friction model, a is assumed to be dependent on axial force N through:

a = α0 + α1*N + α2*N^2

where α0, α1 and α2 are constants, with units of Time/Length, Time/Length/Force and Time/Length/Force^2 respectively.

---

EXAMPLES:

set muSlow 0.12 set muFast 0.18 set nSlow 0.8 set nFast 0.7 set alpha0 25.0 set alpha1 0.0 set alpha2 0.0 frictionModel VelNormalFrcDep 1 [expr $muSlow/pow($W,$nSlow-1.0)] $nSlow [expr $muFast/pow($W,$nFast-1.0)] $nFast $alpha0 $alpha1 $alpha2 3.0

---

REFERENCES:

[1] Bowden F.P., Tabor D. (1964). "The friction and lubrication of solids – part II." Oxford University Press, London, Great Britain, 1964.

[2] Constantinou M.C., Mokha A., Reinhorn A. (1990). "Teflon bearings in base isolation. II: Modeling." Journal of Structural Engineering (ASCE) 1990; 116(2): 455-474

---

RELATED TO:

• Flat Slider Bearing Element
• Single Friction Pendulum Bearing Element
• Triple Friction Pendulum Bearing Element

---

Code Developed by: Nhan D. Dao, University of Nevada - Reno. E-mail: nhan.unr@gmail.com