ConcreteD

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command is used to construct a concrete material based on the Chinese design code.

uniaxialMaterial ConcreteD $matTag $fc $epsc $ft $epst $Ec $alphac $alphat <$cesp> <$etap>

---

$matTag	integer tag identifying material
$fc	concrete compressive strength *
$epsc	concrete strain at corresponding to compressive strength*
$ft	concrete tensile strength *
$epst	concrete strain at corresponding to tensile strength*
$Ec	concrete initial Elastic modulus*
$alphac	compressive descending parameter*
$alphat	tensile descending parameter*
$cesp	plastic parameter, recommended values: 0.2~0.3*
$etap	plastic parameter, recommended values: 1.0~1.3*

---

NOTES:

• Concrete compressive strength and the corresponding strain should be input as

negative values.

• The value $fc/$epsc and $ft/$epst should be smaller than $Ec.
• The default value for $cesp and $etap are 0.25 and 1.15, respectively.

---

EXAMPLE:

Example 1: Simulation of compressive test in Karson and Jirsa (1969).

uniaxialMaterial ConcreteD 1 -27.6 -0.002 3 0.0001 35000 1.0 0.1 0.25 1.15

---

REFERENCES:

• Karsan, I. D., and Jirsa, J. O. (1969). “Behavior of concrete under compressive loadings.” Journal of the Structural Division, 95(12), 2535-2563.
• Ministry of Housing and Urban-Rural Development of the People’s Republic of China. (2010). “Code for design of concrete structures.” GB50010-2010, Beijing, China.
• Ren, X. D. (2010). Multi-scale based stochastic damage constitutive theory for concrete. Doctoral dissertation, Tongji University, Shanghai. (in Chinese)
• Wu, J. Y., Li, J., and Faria, R. (2006). “An energy release rate-based plastic-damage model for concrete.” International Journal of Solids and Structures, 43(3), 583-612.
• Zeng, S. J. (2012). Dynamic Experimental Research and Stochastic Damage Constitutive Model for Concrete. Doctoral dissertation, Tongji University, Shanghai. (in Chinese)

---

Code Developed By:

Zengyong Wan, Decheng Feng, Xiaodan Ren, Jie Li, College of Civil Engineering, Tongji University,